This chapter describes the boards supported by the BSC The BSC UUP (UMTS RNC user plane processing). -. -. 2 GE. 2 GE. Home/Groups/Wireless Network Info Community. BSC e BSC RNC in Pool. Armetta Diamond (1) 4 years 6 months ago View: Reply: 0. Comment. This program provides thorough understanding of 3G Technology, product and hardware description of Huawei RNC , with their data.

Author: JoJorg Gosho
Country: Guatemala
Language: English (Spanish)
Genre: Music
Published (Last): 28 June 2009
Pages: 405
PDF File Size: 4.23 Mb
ePub File Size: 13.64 Mb
ISBN: 524-5-52951-807-3
Downloads: 86725
Price: Free* [*Free Regsitration Required]
Uploader: Fenrill

BSC e BSC RNC in Pool-Wireless Network Info Community-Huawei Connect

When NEs are in the Normal mode, alarms are reported normally. Check whether the DIP switch on the subrack is set as configured. Prerequisite l The preparations for installing software on site are complete.

The Gb interface verification varies according to the transmission mode over the Gb interface. You can choose either way according to your convenience. Note that the user name or password may be modified. The information in this document huaweii subject to change without notice. Key 1, Key 2 Press the keys in turn. Requirements for Equipment Status Before commissioning, ensure that the equipment meets the conditions listed in Table If the value of Link Availability Status is Unavailable, check the connection of the Ethernet cable and check whether the peer Ethernet port is enabled.

Succeeded, If 600 loopback test result is Not Contact the maintenance 9600 for the peer equipment succeeded, to rectify faults in the peer equipment or the transport network.

  MAGELLAN ROADMATE 1400 MANUAL PDF

Action Description Click Select and release the primary mouse button without moving the pointer. For details, see Preparations for Installing Software on Site. NOTE You can also copy the reg. Drag Press and hold the primary mouse button and move the pointer to a certain position. Table Requirements for equipment status before huawie Item Requirement BSC hardware The hardware is installed and passes the hardware installation inspection and power-on check.

Prerequisite l All the subracks and boards are running normally. Remove and then install the OMU board huaaei reset it. The Create Task dialog box is displayed. If yes, clear the alarm as suggested.

Procedure l When the data link layer of the Lb interface is carried on the Abis interface board, verify the Lb interface in the same way as for the Abis rnv. The log-in dialog box is displayed, as shown in Figure Context The time for system resetting is different in different scenarios, as listed in Table Logging in to the OMU remotely, run the ping command to check whether the network connectivity between the BSC and the M is available.

Check the configuration data of rnv license huzwei the configuration data in the OMU database. Product Version The following table lists the product version related to this document. Context There are two ways to verify the Ater interface: Go to step Step 3.

Bsc6900 UMTS/GSM Bsc Rnc 6900 Rnc6900

Context For details about the loading modes, see Loading Management. Then this task is complete.

  CONSTANTIN CUCOS PEDAGOGIE PDF

For example, you can run the following command address of the backup OMU. Context Select a verification method according to the actual scenario.

Step 2 Power on the cabinet by referring to Powering On the Cabinet. It aims to ensure that the BSC can work properly by performing verification tasks related to equipment, BSC board software and data file loading, interfaces, and services. Click OK to complete the setup of enc NE health check scenario. One or more alarms are listed, Go to step Step 3.

Prerequisite l The BSC and the peer equipment are physically connected, and the hardware installation acceptance is passed. Click Upload on the right. After all the information is automatically obtained, check whether the information is correct and enter the information that needs to be typed, as shown in Figure The information returned is running, 1.

Then, locate the MS. Run the ping Table Hiawei for checking the status of transmission link in different transmission modes If the transmission on the interface is Then The Set Data Comparison dialog box is displayed, providing the current device status and the parameters that you set.

The USB disks are prepared.