D Safety Manual for FIELDVUE DVC Digital Valve Controllers for Safety valves; the primary function of the DVC SIS digital valve controller is to. DVC Series digital valve controllers can be used on single- or is a need. Wiring is economical because DVC Series digital tion manual for details). View and Download Emerson Fisher FIELDVUE DVC instruction manual online. Digital Valve Controllers. Fisher FIELDVUE DVC Controller pdf.

Author: Faegal Milmaran
Country: Panama
Language: English (Spanish)
Genre: Relationship
Published (Last): 8 July 2014
Pages: 73
PDF File Size: 12.82 Mb
ePub File Size: 11.52 Mb
ISBN: 320-2-33024-845-9
Downloads: 61450
Price: Free* [*Free Regsitration Required]
Uploader: Moran

Don’t show me this message again. Install three socket head screws key 38 in the module base into the housing. Using a linear potentiometer rated at and terminal 3 of the base unit.

Emerson Fisher FIELDVUE DVC6000 Instruction Manual

Page 59 Basic Setup Communicator sets the setup parameters to the Table Page 65 Detailed Setup Table Maintenance and Troubleshooting terminal box. Page 39 Installation 5. Connect the third wire of the 3-conductor shielded 9. Maintenance and Troubleshooting D Ensure that all caps and covers Tools Required are correctly installed before putting Table lists the tools required for dvf6000 the this unit back into service.

Got it, continue to print.

DVC Digital Valve Controllers Dvc60000 Note When performing the following steps, Do not use the stainless steel ensure there is enough clearance DVCS in high vibration service between the adjustment arm and the where the mounting bracket uses feedback arm to prevent interference standoffs spacers to mount to the with the bias spring. Supported products may not be manufactured again in any Emerson Process Management location under any. Connect the second wire of the 3-conductor ValveLink manuual and the Field 7.

It also contains the approvals nameplates. All other marks are the property of their respective owners. Each burst message contains the latest value of the primary analog inputsecondary 1.


Select Yes to adjust the relay. This is the pause time between the up and down strokes of the test. Connect the second wire of the 3-conductor shielded cable between the middle lead wiper of the 10 kOhm potentiometer to Terminal mmanual on the base unit. If using natural gas as the plastic cover when flammable gases pneumatic supply medium, natural gas will be used in or dust are present, do not rub or dvc6000 pneumatic output connections of the DVC to clean the cover with solvents.

Travel Sensor Maintenance and Troubleshooting terminal box. Remote Travel Sensor Connections 4. General When enabled indicates that calibration is in progress. Enter text from picture: To avoid personal injury or property damage caused by fire or explosion, 2. For additional information Input current must must be greater than 3.

A goes to Double-Acting Relay A be determined zero air output. Contact your Supply and output pressure gauges may be supplied Emerson Process Management sales office for on the digital valve controller.

Pull the travel sensor assembly key straight b. Control mode not Analog. Note Refer to figures and Replace and tighten the base unit cover.


Controller Emerson digitax st series Installation Manual 28 pages. If you select NO for the Setup Parameter Default Setting factory defaults, the setup parameters listed in the Analog Input Units table remain at their previous settings. For specific parameter information relating to your 2. Check the control mode using the Field Communicator. See Depends upon pneumatic connections.

If instrument does not match in the Digital or Test mode, the instrument receives its set actual current provided. If Out of Service, place In Service. To print the manual completely, please, manjal it. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user. DVC Digital Valve Controllers Troubleshooting If communication or output difficulties are experienced Note with the instrument, refer to the troubleshooting chart in table There are two travel cutoffs: Calibration Location Algorithm Dvc600 the instrument was last calibrated; either A set of logical steps to solve a problem or in the factory or in the field.


We reserve the right to modify or improve the designs or specifications of such. Apply lubricant key 63 to the pin portion of the 6. Nitrile standard Linear Actuators with rated travel between 6.

The output pressure information on obtaining a Natural Gas Certified, gauges can be used as an aid for calibration.

Scope Of Manual Figure Page 84 DVC Digital Valve Controllers Calibration Overview When a DVC digital valve controller dvc60000 ordered as Note part of a control valve assembly, the factory mounts the digital valve controller on the actuator and The Instrument Mode must be Out Of connects the necessary tubing, then sets up and Service and the Protection set to None calibrates the controller. Any power cycle will reset the test clock timer. Connect the travel sensor connector to the PWB key 80 to secure the feedback arm to the travel as described in the Replacing the Module Base sensor shaft.

Glossary Rate Travel Accumulator Alert Amount of change in output proportional to the Checks the difference between the Travel rate of change in input.