I have an anilam that quit working. Will the drive motors from the anilam work with a mach 3 system. And where does a person find a. Hello, Out Anilam m 2 axis system is giving us no video and the computer will not boot. Does anyone know how to repair the system?. Anilam is the company that makes the control. I run a Sharp knee mill with a Aniliam M control. I’m not familiar with the M or sure what.

Author: Vudorr Akinobei
Country: Yemen
Language: English (Spanish)
Genre: Environment
Published (Last): 27 April 2018
Pages: 19
PDF File Size: 14.95 Mb
ePub File Size: 14.85 Mb
ISBN: 661-4-26907-468-2
Downloads: 66155
Price: Free* [*Free Regsitration Required]
Uploader: Mojora

Please note the difference between each of the three boards.

Controller & Computer Solutions > Anilam m software

Did the problem stay in the original axis? Once the problem returns, turn the power off and remove the problem cable.

Does the K4 relay on the PC board energize? Make sure the feedrate overide knob isn’t falling off.

If ordering part number s Anilam must know what version software is loaded on the machine. For example, for a rectangular pocket cycle you would fill in X-center Y-center, length, width, depth, depth of cut, z-starting point, amount of material to leave for finish, corner radius, and feeds.

By closing this banner, scrolling this page, clicking a link or continuing to browse otherwise, you agree to the use of cookies. This will usually cause an out of round condition on your part.

Login to Your Account. The cable plugs onto the motion board at location P9 see drawing below for wire connections. Repeat step 3 to verify if the problem moved.

  BITTERSWEET SARAH OCKLER FREE PDF

If the answer is yes, go to Chapter 3. If the answer is yes please check the amperage draw on that motor. If you have a DSP style board system check your programming manual. Follow us on All times are GMT L7 usually is the X limit switch, L8 usually is the Y axis limit switch, and L9 usually is the Z axis limit switch.

Turn the VAC power off again. Take this board to the machine and do the following test. Is the fault light on? Using your arrow key highlight Motion and push the Enter key.

Check the power supply cable on the distribution board plugged onto the P1 connector. Replace the fuse and recheck.

I tried the machine again, and I actually got to the point of loading the control software. This drive card is not an Anilam part. Below the picture, it says ‘battery not replaceable!

This can be cause by the rapid gain not being set properly. You would need to order Part s. If it is you must backup each file one at a time until you have as many of them backed up that are not bad.

For a torque rating of 4. Remove the motion control board only after you touch the cabinet to discharge any static electricity which may have built up on your body.

Series trouble shooting guide

If the encoder is part of the motor and is not easily swapped to another axis, then swap motors to see if the problem will move with the motor into a working axis. Thanks for the quick response. Reboot the computer and check the messages. On this board there is an Anilam part number silk screened on it. Energize the servo and try to move the ballscrew by hand. Put in the bootable Diagnostic disk and reboot the anilsm. Now just plug it right back in.

  KIAI JUTSU PDF

How many potentiometers are on the front edge? If there is a printer connected it MUST be turned on. Anyway, I have to say that Jerry was incredibly helpful, considering that he doing it all for free. I use g-code for Fanuc and DX and now learning this rig. Also, does anyone have anilamm software that runs on the mill? Jerry at Anilam can e-mail you the necessary software to do this operation.

Anilam 1100M Programming Manual CNC Three Axis

If you can’t figure out how to mate the new PC to the servo drivers, replace them with Gecko Drives. Put back in the fuse and see if the voltage still remains OK. Put an indicator in the spindle. Open the door on the computer.